General Electric – Ohmeda Panda 4300

SOLICITAR COTIZACIÓN

SOLICITAR COTIZACIÓN

The GE Ohmeda 4300 Infant Warmer System uses a manual mode of operation that allows selection of the level of radiant heat output as indicated by the % power display on the control panel and the control circuit then maintains the selected level of radiant heat. Servo mode of operation allows selection of the patient’s control temperature and a control system modulates the radiant heat to maintain the patient at the selected control temperature. Alarms activate to alert the operator of a low or high patient temperature, a skin temperature probe failure, a power failure, equipment failure or a check patient prompt

  • Microprocessor Control
  • 20 Segment Output Control
  • Digital Apgar Timer
  • Powered Elevating Base
  • Pre-Heat Mode
  • Dovetail Rail Mounting System
  • Large bed accommodates larger infants easily
  • Bed height adjusts to comfortable working level
  • The GE Ohmeda 4300 Infant Warmer uses an advanced microprocessor system continuously monitor patient and machine status
  • Easy patient access from any location around unit
  • Heater Power: 550 Watts ±5% at maximum % power setting
  • Examination light Luminance: 100 (nominal) foot candles at center of mattress

Description

PDF DEL PRODUCTO

Additional information
MARCA

GE

CONDICIÓN

Reacondicionado Certificado

Más Información

Más Información

GE Ohmeda 4300 Specifications

Dimensions

  • Height: 183 to 203 cm (72 to 80 in)
  • Depth: Both: 114 cm (45 in)
  • Width: Both: 76 cm (30 in)
  • Weight: 4400: Approx. 91 kg (200 lbs)
  • Standard 3 Drawer Pkg: 25 kg (56 lbs)
  • Rotating 3 Drawer Pkg: 32 kg (70 lbs)
  • Standard Deep Drawer Pkg: 25 kg (56 lbs)
  • Rotating Deep Drawer Pkg: 32 kg (70 lbs)
  • Foot Print: Both: 75 X 114 cm (29.5 X 45 in)
  • Floor Space: Both: 8572 sq cm (1327.5 sq in)
  • Bed Size: Both: 61.2 X 76.5 cm (24 X 30 in)
  • Bed to Floor: 98 – 118 cm (38.75 – 46.5 in)
  • Bed Tilting: Both: ±10° Reverse Trendelenburg and Trendelenburg, damped

System Control Characteristics

  • Microprocessor Based Control System: Self-test function performed at power on and continuously during normal operation
  • Heater Output: 0-540 watts power adjustable from 0 to 100% in twenty 5% increments
  • Patient Control (Servo) Mode: 35°C to 37.5°C in increments of 0.1°C (95°F to 99.5°F)
  • Manual Mode: Indicates manual mode heat selection range from 0 to 100% in 5% increments
  • Temperature Variability: Less than ±0.3°C
  • Resolution: ±0.1°C
  • Probe Interchangeability: ±0.1°C
  • Probe Range: 30°C to 42°C (71.6°F to 107.6°F)
  • Proportional heat control with zero voltage switching to minimize radiated and conducted EMI
  • Observation Light: 100-foot candles at center of mattress; estimated lamp life 3000 hours

Heater Assembly

  • The radiant heater provides a focused heat source using a cal-rod heating element, which directs controlled heat to the bed surface
  • The heater assembly, located above the center of the bed, consists of the radiant heater, parabolic reflector, integral observation light, and visible red alarm indicator light
  • The heater module rotates 90 degrees to the side to facilitate X-ray procedures. The heater automatically shuts off when in this position

Bed

  • The hydraulic tilt system provides tilt of up to +10o for positioning in Trendelenburg and reverse Trendelenburg positions
  • The four bedside panels fold down for complete access to the infant
  • The rear panel includes tubing management slots for retention of ventilation and aerosol tubing
  • The bed incorporates an X-ray Cassette Tray. A grid location marking systems on the side panels matches the tray for location of the cassette. Bed construction is radiolucent
  • A chest drainage hanger allows for convenient placement of chest drainage systems